Array VTN-HUNGARY - Legyen vtn kivtelező partnerünk



          

Recommended Resolution:
1024x768
    
To view page perfectly use Internet Explorer.

 

 

    

DIY Fund (DIY package):

- 50cm wide 4FM any film, which is in principle sufficient magnitude and a Smart Cabrio, about 432 pc mobile phone front, approx. 10 laptop cover, approx. 1.349 pc keys, as well as the involvement 8pcs mask (or even very many things which can only view - they are administered stimulus)
- 1 bottle activator spray

14.000 .- net per person rong>14.000 .- net per person

Postal package fee calculator
 

Senior CSMCS (DIY package):

- 50cm wide 4FM any film, which is in principle sufficient magnitude and a Smart Cabrio, approx. Pc 432 mobile phone front, approx. 10 laptop cover, approx. 1.349 pc keys, as well as the involvement 8pcs mask (or even very many things which can only view - they are administered stimulus)

- 1 bottle activator spray
- 1 bottle of base paint
- Clear coat spray bottle 1,
- 1 temperature measurement
- A digital countdown clock,
- 1 snitzer (knife - blade)
- 1 roll of masking tape,
- Abrasive paper,
- 1 pair of gloves, chemical protection.

18.000 .- net per person

Postal package fee calculator

1. Decoration Selection
Select the current pattern of more than 400, or order our devised by the sample. Cut off about the required size. Be larger than 5 cm. The edges of masking paper adhesive glue off the blocks this flow of activator-treated film apart.

View Samples>>

2. Preparation
Involved to prepare the material for polishing. Sanding, foundation. Wipe dry with a soft cloth and dust-free. Take in the initial spray and place it in warm water (spraying in order to perfect), while not warm, and shake about. 3 minutes. Blow off the subject, it is about more overlap. Distance of 20 cm to avoid discharge. Leave to dry for 15-30 minutes. The treated surfaces are no longer in touch. Wait until the primer has dried, have the following workflow.

3. VTN - Foil preparation
The film VTN check the water before you would do. One finger, moisten and thereby touch the foil on both sides. Whichever stick it to the side of the water should do the same. This is usually located outside the coil, if not of vice versa. Cut the desired length, and Spread of approx. 30C ° + / - 2C ° water surface free of air bubbles. If you still have the film under air, it is prudent to be blowing out from under him. The tank should be larger than the cut foil.

4. Activation
During activation of the spray is not to breathe, ventilation is necessary!
During a half-minute soak in the activator shake up thoroughly and then spray it evenly on foil. At this point the film becomes completely liquid, into which 20 seconds of the objects involved should be soaked.

                                                                                 

5. Shuttle - immersion
The floating layer at an angle of 30 degrees, even at speed of an object immersed in the preparations. After depressing the water, move to the right - left, then put the rest of the bond period.

 

6. Washing, drying
Quarter of an hour later, the object immersed in a jet of water (eg shower) the total surplus slippery substance, wash and let dry at room temperature.

7. Lacquered and polished.
Clear coat evenly coated with the subject breath and polishing to achieve a high light. Also put hot water in colorless shiny varnish, and then shake for 3 minutes. Blow off the surface without flowing smoothly around. 20cm's distance. Avoid inhaling the lake!

Good luck and want an aesthetic experience!

 

 

 

The Thomy Folia pages edited by all of the material is under copyright protection. Illegal act of copying, which is always the result of a process of compensation and royalty payment has entail.

Design by Webdesign89.